Online Tone Generator
Generate any tone from 1 Hz to 20,000 Hz right in your browser. Free, no download, no sign-up.
Common Presets
How to use it
- Drag the frequency slider or type an exact value from 1 to 20,000 Hz.
- Pick a waveform: sine for pure testing, square/sawtooth for brighter harmonics, triangle for a softer tone.
- Tap a preset (A440 for tuning, 1 kHz for calibration, 15–18 kHz to test your hearing limit) and press Play.
- Adjust volume to a comfortable level and press Stop when done.
What is a tone generator used for?
- Speaker & subwoofer testing — sweep from low to high to find rattles, buzzes or dead drivers.
- Hearing range check — most adults hear up to 15–17 kHz; younger people hear higher.
- Room acoustics — find standing waves and room modes with low-frequency tones.
- Instrument tuning — A440 reference tone and other musical pitches.
- Tinnitus frequency matching — identify the pitch of ringing in your ears (consult a doctor for treatment).
- Electronics testing — signal injection for amplifier and cable testing.
Explore more tools
Frequency Reference Table
Quick reference for common tones and what people use them for:
| Frequency | What you'll hear | Common use |
|---|---|---|
| 20 Hz | Deep rumble (at the edge of hearing) | Subwoofer / bass extension testing |
| 60 Hz | Low hum | Mains hum check, subwoofer setup |
| 440 Hz | Standard concert pitch A | Instrument tuning |
| 1,000 Hz | Medium-pitch beep | Audio equipment calibration reference |
| 8,000 Hz | Shrill whistle | Treble / tweeter check |
| 15,000 Hz | High-pitched tone only younger ears catch | Quick hearing range check |
| 17,000–18,000 Hz | Near the limit for most adults | Teen deterrent devices, hearing age check |
| 19,000–20,000 Hz | Silent to most adults | Upper hearing limit testing |
Waveforms explained: sine, square, sawtooth and triangle
Every musical or test signal is built from one simple idea: a waveform vibrating at a certain number of cycles per second (Hz). The shape of that waveform decides how the tone feels, even at the same pitch. Knowing which shape to pick turns this tool from a toy into a diagnostic instrument.
Sine is the pure waveform: a single frequency with no harmonics at all. It sounds soft, round and almost flute-like. Because it contains exactly one frequency, it is the only waveform you should use when you are measuring something — checking hearing limits, hunting a room resonance, or comparing two pitches for beats. If a test asks for a "pure tone," sine is what it means.
Square adds all the odd harmonics (3f, 5f, 7f and so on) on top of the fundamental at decreasing levels. The result is bright, harsh and noticeably louder-feeling at the same frequency. That harshness is useful: a square wave pushes more energy into the harmonics, so it can reveal buzzes, rattles and distortion in a speaker that a polite sine wave would glide past. Early video game consoles used square waves for exactly this reason — they are cheap to make and cut through anything.
Sawtooth contains both odd and even harmonics, giving the richest, "reediest" sound of the four — think synth brass or strings. It is a good stress signal for checking how equipment handles dense harmonic content, and it makes sweeps feel more audible at low volumes because the energy is spread across many frequencies at once.
Triangle sits between sine and square: a few odd harmonics at low levels, a gentle hollow tone like a flute or a soft whistle. It is a nice middle ground when a sine feels too quiet but a square feels too aggressive — for example, when testing sensitive in-ear monitors at low volume.
Rule of thumb: measure with sine, stress-test with square or sawtooth, listen comfortably with triangle.
Practical testing scenarios, step by step
Checking speakers and headphones for weak spots
Set the waveform to sine, the volume to about 30%, and walk the frequency upward from 50 Hz in small steps: 50, 100, 200, 500, 1k, 2k, 4k, 8k, 12k, 15k. At each step, note whether the loudness feels even. A good speaker sounds smooth through the whole range. A failing one buzzes at certain notes (a loose driver), goes quiet in bands (a blown tweeter or a port leak), or produces distortion that grows with volume. Do this with a familiar album afterwards: if 100 Hz boomed during the test, bass-heavy songs will sound muddy.
Hunting room resonance
Small rooms have natural resonances — standing waves — that pile up bass at certain frequencies. Play a slow manual walk from 30 Hz to 300 Hz at moderate volume and listen for notes that boom much louder than their neighbours. Those are your room's modes. Move to a different corner and repeat: the booms shift. This tells you why bass sounds different around the room, and why moving a subwoofer even half a metre can transform it. Pair this with the noise generator for a quick overall check.
Matching a tinnitus pitch
Many people who hear ringing want to know its pitch, for example to set a matching masking sound. Slowly sweep from 4 kHz to 16 kHz and stop where the tone feels closest to your ringing; fine-tune with the frequency input. Note the number. You can then use a matching band of noise as a masker. This is a self-help comparison only — persistent or one-sided ringing deserves a proper medical check.
Tuning an instrument by ear
Play A = 440 Hz from the presets, then play the A on your instrument. If you hear a slow wobble (beats) between the two, the instrument is out of tune; tune until the wobble slows to nothing. The beat trick is explained in detail on the multiple tones page.
How accurate is this tone generator?
Frequency accuracy is excellent: the tone is generated digitally from your browser's audio clock, typically a quartz-derived crystal accurate to within a few parts per million. A 440 Hz tone here is at least as accurate as a decent physical tuner — far more accurate than you can perceive, since human pitch discrimination is roughly 0.5% even for trained listeners.
The honest limits are in the output chain, not the math. Your sound card, amplifier and speakers decide what actually reaches your ears. Laptop and phone speakers usually roll off below 200–400 Hz and above 15 kHz, so a 50 Hz tone may be inaudible or mostly a faint harmonic — that is the hardware, not a bug. Consumer DACs run at 44.1 or 48 kHz sample rates, which caps output just above 20 kHz (the Nyquist limit). Volume is uncalibrated: "30%" on this page is not 30 dB, it is a relative level that depends on your device. For anything that matters — hearing assessment, acoustic measurement — use dedicated calibrated equipment. For everything else, this is comfortably accurate.
Hearing safety: how loud is too loud?
Loud tones are the one real hazard this tool has, and it is entirely controllable. Occupational safety guidelines treat about 85 dB as the maximum safe exposure for eight hours, and every 3 dB increase halves the safe time: 88 dB for four hours, 91 dB for two, and so on. Test tones feel less loud than music at the same energy because they lack rhythm and variation, which makes it tempting to push the volume — resist that.
Three practical rules. First, start every session at low volume and raise it only until you can clearly hear the tone; you rarely need more than a third of the slider. Second, never put your ear next to a speaker or driver, especially during sweeps: a high-frequency tone at close range can deliver real acoustic energy while feeling deceptively quiet. Third, if you notice ringing, fullness or muffled hearing afterwards, that is temporary threshold shift — a warning from your ears. Stop, rest in quiet for a day, and use lower levels next time. Children's ears are more delicate; keep volumes lower for them, and keep the volume down when a pet is in the room, since dogs and cats hear frequencies you cannot.
A short history of the test tone
Before electronics, the only portable tone generator was the tuning fork, invented by English musician John Shore around 1711 — he called it a "pitch fork." Orchestras tuned to one for two centuries, though not always to the same pitch: A wandered between roughly 380 and 480 Hz depending on city and era. An international conference fixed A = 440 Hz in 1939, and ISO 16 confirmed it in 1955, which is why every tuning reference on this site centres on that number.
Electronic oscillators entered laboratories and recording studios through the twentieth century: test-tone tracks were pressed onto calibration records, broadcast as tuning bars before programmes (the EBU's 1 kHz reference tone still opens many broadcast masters), and used to align tape machines and mixing desks. What once required a bench oscillator or a special vinyl disc now runs in a browser tab for free — same physics, friendlier packaging.
No sound? Common fixes
Browsers only allow audio after you have interacted with the page, so if nothing plays, tap any button once — this site starts the audio engine on your first click. Still silent? Work down this list: check the device is not on silent mode (the iPhone mute switch mutes web audio); check both the browser tab volume and the system volume; if you use Bluetooth headphones, remember some cheap models mute or distort above 15 kHz, and codecs add a split second of latency; try another browser — Chrome, Firefox, Safari and Edge all support the Web Audio API, but very old versions may not; and if you have multiple output devices (monitor speakers, HDMI, headset), make sure the one you are listening to is the default. One more quirk: some USB audio interfaces need to be set to a standard sample rate before high-frequency tones play correctly.
Frequently Asked Questions
Is this tone generator really free?
Yes — 100% free, no sign-up, no download, no watermark. Everything runs locally in your browser with the Web Audio API; your audio never leaves your device.
What is the highest frequency humans can hear?
Healthy young adults typically hear up to 17–20 kHz. This drops with age to roughly 12–14 kHz by your 50s. Curious where your own hearing tops out? Take our online hearing test to find your limit, or explore the binaural beats and frequency presets tools.
Why can't I hear anything below 20 Hz or above 20 kHz?
20 Hz–20 kHz is the standard human hearing range. Below 20 Hz you feel vibrations more than you hear them; above 20 kHz, dogs and some young people may react while you hear nothing — and most speakers physically cannot reproduce them.
Why does a square wave sound louder and harsher than a sine wave at the same frequency?
A square wave adds odd harmonics (3f, 5f, 7f…) on top of the fundamental, so it contains more energy and sounds brighter and harsher. Sine is a pure single frequency — the cleanest choice for testing.
Is it safe to play loud tones?
Keep the volume moderate. Prolonged exposure to tones above ~85 dB can damage hearing — especially high frequencies near 15–20 kHz, which sound deceptively quiet but carry real energy. Never put your ear next to a speaker during a sweep.
Can I use this to repel mosquitoes, dogs or rodents?
It's a popular idea but doesn't reliably work. Mosquito-repellent apps are ineffective; dogs may react to 20–25 kHz tones but habituate quickly, and most speakers can't produce those frequencies loudly enough.