Bass Test Tone

Pure low-frequency tones from 20 to 120 Hz, straight from your browser. Use them to test a subwoofer, tune a car audio system, find room modes or check how low your speakers actually go — no test files to download and no app to install.

What a bass test tone is

A bass test tone is a single, steady low-frequency note — a sine wave — played through your audio system so you can judge how it handles the bottom octaves. Music hides its bass inside drums, bass guitars and synth lines that constantly change pitch, which makes it hard to tell whether a weak note is the recording, the room or the equipment. A pure tone removes that uncertainty: pick 40 Hz, press play, and whatever you hear (or fail to hear) is entirely about your system and your room.

The frequencies on this page cover the range that matters. 20 Hz is the accepted floor of human hearing and the deepest excursion most movie soundtracks ask of a subwoofer. 30 to 60 Hz is where bass guitar fundamentals, kick drums and most cinematic rumble live. 80 to 120 Hz is the upper bass and the region where a subwoofer hands the job back to the main speakers, which is why 80 Hz is the classic crossover point. Walking up through the range one tone at a time tells you far more than any single test file can.

How to test a subwoofer step by step

Set the volume low to start — a third of the way up is plenty — and pick 40 Hz. Press play and listen from your usual seat. You should hear a smooth, even note. Now step through the presets: 30, 50, 60, 80 Hz. As you go, listen for four things. First, output: does every tone sound roughly equally strong? Second, purity: the note should be a clean hum, not a buzzing or flapping. Third, consistency: walk around the room and notice how wildly the loudness changes — that is the room, not the subwoofer. Fourth, cutoff: find the point where the main speakers take over and the sound loses weight, usually somewhere between 60 and 100 Hz depending on your crossover setting.

For a deeper test, compare 20 Hz against 40 Hz. Very few bookshelf speakers produce anything meaningful at 20 Hz — if a small speaker seems to play it, you are probably hearing distortion products an octave up rather than real bass. A true subwoofer should render 20 Hz as a felt pressure more than a heard pitch. If the driver visibly moves but you hear almost nothing at the listening position, the tone is being produced but the room is not supporting it at that frequency; try the room-mode section below.

Setting subwoofer level and crossover

Two setup tasks use these tones directly. To set subwoofer level, play 50 Hz and adjust the subwoofer's own gain until the bass feels present but never dominant — a common trick is to set it so the note sounds like it comes from the front speakers, not from the corner the sub sits in. If the 50 Hz tone draws attention to itself as coming from a box beside you, the level is too hot. To check the crossover, sweep from 60 Hz up through 100 Hz and find where the sound thins out; your crossover should sit slightly above that point. If voices and bass sound disconnected, or bass seems to vanish between the sub and the speakers, the crossover region is the first place to look.

Using bass tones in a car

Car audio benefits even more from steady tones, because a car cabin is a small, sealed space with brutal standing waves. Play 40 Hz from the driver's seat: in many cars it will sound dramatically louder there than the same tone plays in an open room, while 60 or 80 Hz may sound comparatively weaker — that inversion is normal cabin gain at work. Step through the presets to find where your system's output peaks and dips, then use the sweep generator for a continuous low-frequency walk if you want to map the whole range in one pass. Rattling trim panels announce themselves instantly on a steady tone; press play at 50 Hz and any loose door card or license plate will sing along.

Finding room modes and placement problems

Every room has resonant frequencies — standing waves — that pile up bass at some spots and cancel it at others. To find yours, play 40 Hz and slowly walk from one corner of the room to the opposite one. You will hear loudness swell and fade; the spots where it booms are pressure points of a room mode. Note roughly where they fall, then try the same walk at 30 Hz and 60 Hz. Knowing your modes explains why bass sounds great in one seat and gutless in another, and why moving a subwoofer even half a metre can smooth a terrible dip. The classic "subwoofer crawl" borrows this idea: put the sub at your listening position, play a repeating low tone, and crawl around the floor to find where the bass sounds best — that spot is where the sub should live. Pair the tones with pink noise when you want a broadband check afterwards.

Diagnosing distortion, chuffing and rattles

Steady bass tones are the fastest way to expose hardware problems. A clean sine at moderate volume should sound pure at every preset. If the note buzzes or breaks up at low volume, something in the chain is distorting — a failing driver, an over-driven amp or a port. Ported subwoofers and speakers often "chuff": a windy, turbulent noise on deep, loud passages that means the port is too small for the air moving through it. Play 25 or 30 Hz at gradually increasing volume and listen for the wind noise arriving. Loose hardware betrays itself too: 45 to 55 Hz makes gate hinges, picture frames and dust covers buzz. Finding which item rattles at which frequency is genuinely useful — you can pad it before it ruins movie nights.

Volume, hearing and equipment notes

Low frequencies carry enormous energy, and deep tones at high volume are felt in the chest long before they sound loud. Keep levels moderate while testing; a few seconds at each preset is enough to judge a system, and there is no benefit to minutes of sustained 30 Hz at high gain. If you hear nothing at 20 to 30 Hz even at healthy volume, suspect the equipment first — many laptop and phone speakers physically cannot move enough air, and desktop speakers rarely reach below 60 Hz. Testing with headphones? Most consumer headphones reach 20 Hz on paper, but leakage and fit change the result, so treat headphone bass tests as rough guides only.

A band-by-band tour from 20 to 200 Hz

Reading bass results well means knowing what each band is supposed to prove. From 20 to 30 Hz lies true sub-bass: at these depths you are testing whether a subwoofer can pressurise a room and whether its driver survives the enormous excursion the frequencies demand — many systems that sound impressively deep on music simply have nothing here. From 30 to 60 Hz sits the deep bass of action-film rumbles and the lowest fundamentals of bass guitars and pipe organs; a hump here makes explosions overwhelming, a dip here makes them polite. From 60 to 100 Hz lies the punch band where kick drums and most bass lines actually live — most of what people call bass in ordinary music is this band, and if music sounds thin, the suspect is usually 60 to 100 Hz rather than 30. From 100 to 200 Hz is upper bass: warmth for vocals and body for acoustic instruments, but also where boominess, muddiness and door-rattle problems hide. Sweep slowly through each band with the tool above and note where the level swells, dips or buzzes; a repeatable map of those three things is worth more than any single dramatic moment at 25 Hz.

Break-in, driver stress and when to stop

New loudspeaker drivers genuinely stiffen over their first hours, and the sensible break-in method is several hours of varied music at ordinary listening volume — not minutes of maximum-gain sine waves, which push continuous single-frequency excursion through a suspension that varied program material would have exercised more gently. During any test, the driver itself sends clear distress signals, and every one of them means stop immediately rather than push on. A scraping or grinding texture is the voice coil physically rubbing — sustained, it will score the coil and permanently damage the driver. A steady airy chuffing from a ported box is port turbulence: the port has exceeded its airspeed, the output below it collapses, and the fix is lower volume, not curiosity about how loud it gets. A sharp cracking transient means the driver has reached its mechanical limit and is bottoming out. And if a system distorts at modest volumes across the whole bass range — long before any of those dramatic signs — retest with several music tracks before blaming the tone page; consistent distortion at everyday levels points to an amplifier fault or a damaged driver, not to the test.

Frequently asked questions

What frequency should I use to test a subwoofer?

Start at 40 Hz for a general check — it is deep enough to exercise the subwoofer and common in music. Use 20 to 30 Hz to probe its lowest extension, and 80 to 100 Hz to check the crossover to your main speakers.

Why does 20 Hz sound quieter than 40 Hz?

Human hearing rolls off sharply below about 30 Hz, and most rooms cannot reinforce the longest waves, so 20 Hz is naturally faint and felt more than heard. If it is entirely inaudible, the speaker may simply not produce it.

Can bass test tones damage my speakers?

Not at sane volumes. Damage comes from over-driving: a tone that makes the driver visibly strain, buzz or chuff at high volume. Keep the level moderate and back off the moment distortion appears.

My sub hits hard on music but not on these tones. Why?

Music bass is intermittent, so it sounds bigger than it is. A steady tone also exposes a built-in "loudness" boost or a roomy 50 Hz hump that music hides. Trust the tone, not the demo track.