Frequency Sweep Generator

Sweep audio from one frequency to another to test speakers, headphones and your hearing range end to end.

What is a sweep generator used for?

How to run a sweep

  1. Set the start frequency (From), end frequency (To) and duration. 20 Hz → 20,000 Hz over 30 seconds is the classic full-range test.
  2. Choose Linear for a constant Hz-per-second climb (good for hearing tests) or Logarithmic so every octave takes equal time (better for judging speakers).
  3. Start at a low volume, then raise it — full-range sweeps at high volume can be unpleasant and stress small speakers.
  4. Listen for problems: buzzes indicate loose parts, sudden volume dips mean crossover or cabinet issues, and harshness around 2–5 kHz is normal but should not distort.
  5. Repeat with your volume knob and listening position changed to compare results quickly.

Sweep tips

Linear versus logarithmic sweeps

The sweep range matters less than the path it takes. A linear sweep climbs at a constant number of hertz per second: from 20 Hz to 20,000 Hz in 30 seconds it spends the whole first second crawling through 20–67 Hz, and less than a tenth of a second between 15 kHz and 20 kHz. Bass gets all the attention; treble rushes past. A logarithmic sweep climbs at a constant musical interval instead — like sliding up a piano one octave at a time — so every octave gets equal time and the pitch feels to the ear like a smooth, accelerating whistle.

Choose the mode by what you are hunting. Logarithmic is the right default for almost everything: speaker checks, room modes, hearing-limit estimates, because our perception of pitch is logarithmic and so is the octave layout of speakers and crossover design. Linear sweeps have one specialised home — vibration and structural testing, and some measurement protocols where equal spacing matters for the analysis software. If in doubt, use log.

Duration changes the resolution of what you can hear. Ten seconds is a quick health check. Thirty seconds gives you time to notice a buzz, locate it, and decide whether it is the speaker or something rattling on a shelf. Two minutes and up turns the sweep into a meditation-grade slow scan, which is surprisingly good for finding the exact frequency where a room resonance lives: stop the sweep the moment a note booms and read the number off the display.

How to test a speaker step by step

Put the speaker in its normal position, clear the room of loose objects that can rattle (glasses, radiator covers, curtain rails), and set volume to a modest listening level — about a third up, never loud on the first pass. Run one 30-second logarithmic sweep from 20 Hz to 20 kHz and just listen. On a healthy speaker you will hear a smooth slide, thick at the bottom, thinning as it rises, fading out somewhere between 15 and 20 kHz. Problems announce themselves clearly: a buzz that appears only in a narrow band usually means a loose driver, a cracked dust cap or something mechanical resonating nearby; a sudden hole where the sound vanishes marks a dead band, often a failed tweeter or a disconnected crossover section; harsh crackling that grows with volume suggests a damaged voice coil rubbing.

Run the sweep twice more: once quieter (some faults only show at low excursion) and once louder (rattles hide at low volume). If a fault appears in both speakers identically, it is probably design or position; if it appears in one speaker only, swap channels to confirm it follows the speaker. Finish by sweeping each unit in a pair separately — stereo pairs hide one dead tweeter surprisingly well.

Using sweeps to understand your room

A room is an instrument, and a sweep plays it. Below about 300 Hz, rectangular rooms have discrete resonances — standing waves between parallel surfaces — that make certain notes boom and others vanish. Sweep slowly from 30 Hz to 300 Hz and stop wherever the sound swells dramatically; each swell is a room mode. Write down its frequency. Now stand in another corner and repeat: the booming notes move, which proves the problem belongs to the room, not the speaker. The classic fix is physical, not electronic — move your listening seat away from the exact centre of the room (where the deepest nulls sit), pull speakers off the wall, or add soft furnishings and bass traps. An equalizer can cut a boom, but it cannot fill a null where the wave simply cancels.

Above 300 Hz, sweep once more while walking around the room. Listen for flutter echo — a metallic zang as the sweep excites repeated reflections between hard parallel walls — and for dead spots near corners. This five-minute tour explains more about why recordings sound different around the house than any spec sheet.

Checking subwoofers and crossovers

Subwoofers live or die in the 20–100 Hz band, so give them a dedicated slow logarithmic sweep across just that range at moderate volume. Listen for three things: the lowest note where the driver produces real, physical output rather than inaudible vibration; any chuffing or port noise at high excursion (air turbulence in the port, not a fault, but it limits clean output); and dead spots in the room where the bass nearly vanishes — those are seat positions in nulls, and moving the couch a metre can rescue them. To check a two-way system's crossover, sweep across the crossover region (often around 1.8–3 kHz) and listen for a lump or dip where the handover happens; a deep notch there usually means the tweeter and woofer are wired out of polarity.

Precautions for ears and equipment

Two cautions keep sweeps safe. Your ears: never start loud, and never approach a driver mid-sweep — narrowband energy at close range is genuinely dangerous to hearing, and high frequencies feel quieter than the power they carry. Your equipment: long, loud low-frequency sweeps can overheat small drivers and amplifiers; subwoofer producers routinely cook budget units this way. Thirty seconds at a third of your normal listening volume tells you everything a speaker can tell you. Finally, a small practical note: phone speakers physically cannot reproduce a 20 Hz sweep — you will hear faint harmonics instead. That is a hardware floor, not a software fault; use real speakers or headphones for anything below 200 Hz.

Frequently Asked Questions

Linear or logarithmic sweep — which should I use?

Logarithmic for listening tests (each octave gets equal time, matching how you hear); linear for measurement and vibration testing, where equal Hz-per-second matters.

Why does my speaker buzz or rattle during a sweep?

A rattle at one specific frequency means something loose is resonating — a panel, a screw, or the driver itself is damaged. Note the frequency where it happens and check that part.

What sweep range should I test a subwoofer with?

20–120 Hz covers the subwoofer band. For full-range speakers use 20 Hz–20 kHz and listen for dropouts or distortion anywhere in the range.

What is the difference between linear and logarithmic sweep?

A linear sweep climbs at a fixed number of Hz per second, so low frequencies rush past and high ones crawl. A logarithmic sweep doubles the frequency in equal time steps, giving each octave the same duration — better for evaluating speakers and headphones.

Why does the sweep get quieter at the very low end?

Small speakers and phone speakers cannot reproduce deep bass — at 20–60 Hz you may feel little or hear nothing even though the tone is playing. That is a hardware limit, not a bug.

Can a sweep damage my speakers?

A sweep itself is no more stressful than music, but sustained output at maximum volume generates real heat in voice coils. Use moderate volume and avoid leaving a full-volume sweep looping for hours.

What sweep range should I use for a hearing test?

Sweep slowly from 8,000 Hz upward at a comfortable volume. The point where the tone seems to vanish is roughly your upper hearing limit — usually 15–17 kHz for adults, higher for children.

Why do I hear a second, lower tone during the sweep?

You are hearing harmonic distortion or intermodulation from your playback chain, or an acoustic beat against a reflected wave in the room. Clean systems produce a single smooth rising tone.

Does the sweep run if I switch browser tabs?

In most browsers yes, but some throttle background audio timing. Keep the tab visible during a test sweep for accurate results.

Common questions about frequency sweeps: